IAE Academy

FIRST YEAR · CHEMISTRY · CHAPTER 7 OF 8

Water: hardness and treatment

This chapter explains water hardness and how it is measured, the boiler troubles it causes, softening, and how river water is made safe to drink. Every boiler and cooling circuit depends on the water fed to it.

Updated 30 Oct 2026

What you will be able to do

You will state hardness in mg/L of calcium carbonate equivalent and measure it by EDTA titration. You will match each boiler trouble to its prevention and work out the lime and soda a sample needs. You will describe zeolite, ion exchange and municipal treatment.

Before you start

  1. Moles and molar mass, and mole ratios in a balanced reaction

  2. Molarity (mol/L) and how a titration reaches an end point

  3. pH, what a buffer does, and the hydrolysis of a salt in water

  4. Writing and balancing simple ionic reactions

Hardness and how it is measured

Water is hard when it will not lather easily with soap: its calcium and magnesium ions, dissolved from rocks such as limestone and gypsum, turn soap into an insoluble scum. Hardness is temporary when the salts are bicarbonates, because boiling removes them: and . It is permanent when they are chlorides and sulphates, which boiling leaves in solution. Total hardness is the sum of the two. Salts of different molar mass cannot be added by mass, so each is restated as the mass of (100 g/mol) with the same moles of or .

CALCIUM CARBONATE EQUIVALENT

Holds for a salt with one or per formula unit. is its concentration (mg/L), its molar mass (g/mol) and the hardness in mg/L as . For dilute water 1 mg/L is 1 ppm.

EDTA binds each or ion 1 : 1, more strongly than the indicator Eriochrome Black T does. An ammonia buffer holds the sample at pH 10, where EDTA binds both ions firmly and the indicator is wine red when bound to them and blue when free. At the end point EDTA has pulled the last ions off the indicator, so the colour turns blue.

HARDNESS FROM AN EDTA TITRATION

Holds when every and ion reacts 1 : 1. is the total hardness (mg/L as ), the EDTA molarity (mol/L), the EDTA volume (mL) and the sample volume (L). is in mmol, each worth 100 mg of .

WORKED EXAMPLE

A 50.0 mL water sample needs 12.5 mL of 0.0100 M EDTA to reach the end point. Find its total hardness in mg/L as .

Solution
  1. EDTA used mmol, since mol/L times mL gives mmol.

  2. The reaction is 1 : 1, so this is 0.125 mmol of equivalent, or 12.5 mg at 100 mg per mmol.

  3. The sample is 0.0500 L, so mg/L.

Answer: 250 mg/L (ppm) as

Boiler troubles

In a boiler, water leaves as steam and the salts left behind grow more concentrated. They, with dissolved gases, alkali and oil, cause the troubles below.

Trouble

What happens

Prevention

Scale

Hard crust of , or on hot surfaces; it wastes fuel, and the overheated plate can burst

Soften the feed water. Inside the boiler, phosphate precipitates calcium in the water, not on the metal, as loose :

Sludge

Loose precipitate (, that phosphate) settling in cooler parts; it can clog pipes

Soft feed water; regular blow-down (draining off some concentrated water)

Priming

Water droplets carried over with the steam, from fast steam flow, a high water level or a sudden demand

A low, steady water level; even steam draw; clean, soft water

Foaming

A lasting froth on the surface, from oil or alkali

Remove oil; add an anti-foaming agent; blow down

Caustic embrittlement

Soda, , left from lime-soda softening hydrolyses at high pressure: . The NaOH concentrates in joints and cracks the stressed iron

Sodium phosphate instead of soda; tannin or lignin to seal hairline cracks

Boiler corrosion

Dissolved rusts iron; makes the water acidic; hydrolyses to HCl

Deaerate, or add sodium sulphite or hydrazine; ammonia against acid; soften

Softening and municipal treatment

The lime-soda process adds lime, , and soda, , so that calcium and magnesium leave as insoluble and . The table gives each reaction and the moles of lime and soda per mole of equivalent; temp means bicarbonate hardness, perm chloride and sulphate hardness.

Constituent

Reaction

Lime

Soda

1

0

2

0

1

1

0

1

Free

1

0

LIME REQUIREMENT

Holds for pure lime, per litre, when the water holds only the table's constituents. Terms are in mg/L as (free converted with ); the coefficients are the lime column, and 74 g/mol for gives mg/L of lime.

SODA REQUIREMENT

Same conditions and units, for pure soda; 106 g/mol for gives mg/L of soda. appears because lime turns it into an equal amount of or .

WORKED EXAMPLE

One litre of water holds 81 mg (162 g/mol), 73 mg (146 g/mol), 60 mg (120 g/mol) and 136 mg (136 g/mol), and no free . Find the lime and soda needed.

Solution
  1. The formulas take equivalents, so convert each with : , , and mg/L.

  2. Lime mg/L; counts twice because each mole takes two moles of lime.

  3. Soda mg/L, for the original and the lime made from .

Answer: Lime 148 mg/L and soda 159 mg/L, that is 148 g and 159 g per 1000 L.

The zeolite process passes hard water through a bed of sodium zeolite, , where Z stands for an insoluble aluminosilicate framework. The bed takes up calcium and magnesium and releases sodium, and brine (concentrated NaCl) regenerates it. Iron, manganese and turbidity are removed first, since they foul the bed.

ZEOLITE SOFTENING AND REGENERATION

Holds for in the same way. Left: softening. Right: regeneration, after which the is washed away. The water gains sodium salts but no hardness.

Ion exchange gives demineralised water. and stand for insoluble polymer resins. A cation resin swaps cations for , as in ; an anion resin then swaps anions for , as in . The and form water. Dilute acid regenerates the cation bed, dilute alkali the anion bed.

Municipal treatment makes water safe to drink. Sedimentation settles coarse silt. Coagulation adds alum, whose reacts with the water's bicarbonate: . The jelly-like floc traps fine particles as it sinks. Sand filtration removes the rest, and chlorination kills germs.

DISINFECTION BY CHLORINE

Holds for chlorine dissolved in water. Hypochlorous acid, HOCl, kills microbes by destroying their enzymes. A small free chlorine residual keeps the water safe in the pipes; too much spoils its taste and smell.

Check yourself

CHECK YOURSELF 1

A water sample contains 120 mg/L of (120 g/mol) and 111 mg/L of (111 g/mol), and no other hardness salt. Its total hardness as equivalent is:

  1. (A)

    231 mg/L

  2. (B)

    200 mg/L

  3. (C)

    100 mg/L

  4. (D)

    115.5 mg/L

Answer and solution

Answer: (B)

  1. Convert each salt with before adding: and mg/L.

  2. Total mg/L. Adding the salt masses (231) is wrong.

CHECK YOURSELF 2

A 25.0 mL water sample needs 10.0 mL of 0.0100 M EDTA to reach the end point. Find the hardness in mg/L as .

Answer and solution

Answer: (accepted range )

  1. EDTA used mmol, which is 10.0 mg of .

  2. mg/L.

CHECK YOURSELF 3One or more options are correct

Which of the following statements are correct?

  1. (A)

    Priming is the carry-over of water droplets with the steam.

  2. (B)

    Caustic embrittlement is cracking of stressed boiler iron by concentrated NaOH.

  3. (C)

    Sludge is a hard adherent deposit that is difficult to remove.

  4. (D)

    The zeolite process replaces the calcium and magnesium of hard water with sodium.

Answer and solution

Answer: (A), (B), (D)

  1. A and B are the definitions of priming and caustic embrittlement.

  2. C describes scale; sludge is soft and loose, so C is wrong.

  3. D is how sodium zeolite works.

CHECK YOURSELF 4

One litre of water holds only , equal to 30 mg/L as , and no free . Find the lime needed in mg/L of pure .

Answer and solution

Answer: (accepted range )

  1. Only mg/L is present, and each mole of it takes two moles of lime.

  2. Lime mg/L.